![]() ![]()
Anyway, again, thank you for your help, and i hope i can bother you if something comes up. I'm not looking forward to convince my community to anything because i think it would make more sense to find/create a ADX definition file for this Hardware.Īlso, it would be done faster i didn't know that for the testing the interface it would need any file, i thought the files are needed to actually connect to the ECU. Perhaps you could convince your community to create a plug-in for this. Thank you in advance for your help Jan (Greece) Mangus TunerPro Author Joined: Posts: 1791 Posted: Mon 12:20 pm Post subject: TunerPro cannot talk to the hardware without a proper ADX definition, or a proper plug-in designed for your hardware. Sunbeam Joined: Posts: 9 Posted: Sat 12:01 pm Post subject: Data Acq./Emulation, to configure and test the KWP2000+ Interface to go to the next step. Take a look in your device manager to verify the port number for your cable. Are you sure that the cable is on COM1?ĬOM1 is usually used by native serial connection, USB, and Virtual COM ports through USB usually show up as higher port numbers. Six_Shooter Joined: Posts: 590 Posted: Sat 11:01 am Post subject: Ok, wanted to make sure of the test first. #Kwp2000 usb to serial driver pro#Its actually strange, because i think one guy here, had positive tests with Tuner Pro with the KWP2000 Interface on a ASTRA!!!! My case i would say. At this point (the test) i haven't loaded any file (ADX, XDF or what all the extensions are), because to get there, i have to make sure, TunerPro 'sees' my Hardware (Cable) first. It states that: CABLE NOT FOUND OR NOT FUNCTIONING (TESTED AT 8192 BAUD). I actually did perform the CONFIGURE PLUGIN COMPONENT, and then selected the COM PORT as STANDARD SERIAL (otherwise by selecting SHARED WITH EMULATOR, the COM port cannot be selected), but when i pressed TEST FOR VALID. Sunbeam Joined: Posts: 9 Posted: Sat 7:13 am Post subject: Six_Shooter, thank you for your reply. Make sure it is disconnected from the vehicle when performing this test. I'm not sure if this would work with the cable you are trying to use, but this button/test works with the interfaces used with GM vehicles. Does TP RT V5 see the cable when you use the 'Test for cable' button. It sounds like you went to the right spot, but did you use the 'Configure Plug-in Component' button. I see this as one issue.Īnother issue could be setup for the cable itself. The ADX file is used by TP RT V5 to decipher the incoming datastream, since different cars or rather different ECMs and their respective codes use different datastreams. Jan Six_Shooter Joined: Posts: 590 Posted: Sat 3:49 am Post subject: For starters, to datalog you need and ADX file. Tried under TOOLS ->PREFERENCES ->DATA ACQ./EMULATION almost everything. #Kwp2000 usb to serial driver drivers#Thing is, either on Windows 7 (64-bit, with drivers from the KWP 2000+ Chip manufacturer) or Windows XP (32-bit with drivers from KWP2000+ installation CD), the TunerPro RT 5 did not 'see' the Interface. When i connected it this morning to a Windows XP Laptop and installed the drivers, it showed up as Serial to KLine Interface, but without giving me any COM port. On device manager it comes up as USB Serial Port, i even get an COM port (COM1). But to get there, i have to get the ECU on a file on my harddisc Thank you in advance and keep up the good work Jan (Greece) sunbeam Joined: Posts: 9 Posted: Sat 1:28 am Post subject: forgot to mention that, on windows 7 64-bit, the drivers from the KWP2000+ did not work, i had to use the ones from FTDI website (KWP2000+ uses the D2XX chip). #Kwp2000 usb to serial driver software#Please, if anybody had any positive experience with this combination, help would be appreciated, since TunerPro is exactly the software to rewrite the ECU the way i would like to do it. I know that there are no related files (bins etc) for this particular car around but this is not the issue here. ![]() But when the time came to use this interface with TunerPro RT 5 (beta), no connection whatshowever with the ECU. Anyway, got it, and started to get to know it. After weeks of searching, i came across the KWP2000+ USB hardware, which seemed to be the right solution for my plans. Now its time to get into the ECU Remapping and Reprogramming. The Z12XE Engine uses the same ECU as the Z20LET. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |